Sample approval on a custom order placed in China is not one event. It is a series of gates, each with a different question and a different record. A prototype answers whether the idea works. A pre-production sample answers whether the intended process can make it. A golden sample answers what the finished run will be judged against. Buyers who collapse those three into a single approved email usually discover the difference after the container is packed. This guide sets out the gates we hold on the buyer’s side for China orders, the deviation record each one produces, and how the approved sample connects to inspection and to the next reorder. We are a sourcing, QC and freight partner, not a factory.
The short answer: what each gate actually approves
Three gates, three different approvals. A prototype answers whether the idea works; a pre-production sample from the intended tooling answers whether the real process can repeat it; a golden sample answers what the finished run will be judged against. Each gate needs a written record: measured critical characteristics, a deviation log with an accepted-or-rejected decision, and an approval sheet naming the sample ID, revision, signatory and what remains open. Approve physical samples – photographs and digital mockups are communication tools, not acceptance standards. Keep two signed masters with unique IDs, one on each side, and tie them to the same frozen file revision that pre-shipment inspection will use on the finished batch.
The three gates, and what each one is allowed to approve
A gate is only meaningful if it can say no. Write down the acceptance question before the sample arrives, otherwise the review becomes a conversation about appearance.
Question: does the geometry, function and assembly work at all? Record dimensions against the drawing, material identification, function tests and photographs. A prototype made by a different process is evidence of intent, not of production capability. Factory verification should already be done.
Question: can the real process repeat this? The sample should come from the intended tooling, material lot, finish and packing method. Record the machine or tool identification, process settings and any special operations. Tooling terms should be agreed by this point.
Question: what exactly will the finished run be judged against? Sign and date two masters with unique IDs, photographs and seals; keep one on each side. Freeze the specification, artwork revision, label copy and carton marks at the same moment. Pre-shipment inspection uses this master.
Question: did the batch start from the frozen configuration? Check the first articles off the line against the golden sample and the current revision before the run continues. Any substitution goes through a written change note, not a chat message.
Question: does the master still describe what we are about to buy? Re-open the file at every reorder, confirm colour and material references, and check whether retained spares or a retained sample still exist. Repeat stock is where silent drift is most costly.
The three records that make an approval defensible
An approval without these records is an opinion. With them, a dispute about a finished batch becomes a comparison against something both parties signed.
Critical characteristics from the drawing, measured values, method, equipment, date and the revision measured against. Tolerance callouts and the gauge chart keep the units and general tolerance unambiguous.
Every difference from the specification, with a photograph, a proposed action and an explicit accepted-or-rejected decision. Accepted deviations become part of the frozen file, not a private understanding.
Sample ID, revision, signatories, date, what is approved, what is explicitly not approved, and which documents the approval covers. Custom manufacturing projects use the same freeze-and-approve discipline.
Where approvals quietly break down
The most common failure is a sample approved from a photograph. A photograph shows colour and shape under one light source; it cannot show a material grade, a wall thickness, a surface standard or whether the logo survives handling. Ask for the physical sample and the measurement record together, and operate the item the way a customer would. For printed packaging, a physical proof also tells you what the chosen substrate does to the colour, which no screen mockup can. Custom packaging covers that file handover.
The second failure is approving one supplier’s sample and then buying from another, or approving a hand-made sample and accepting a machine-made run. Insist that Gate B comes from the intended production tooling, and name the tool or process in the record. Capability verification and process-specific checks help confirm that the supplier can actually repeat what it showed you.
The third failure is a change made after approval. A cheaper component, a new colour lot or a revised label can all enter the batch through a side conversation. Every change should get a written note, a decision on whether the golden sample still stands, and a revised inspection reference. Our procurement service holds the master file so those decisions are visible to the product, packaging and freight sides at once; shipping then works from the same carton and mark data.
Gate, evidence, and the decision it authorises
| Gate | Evidence to file | What it does NOT authorise |
|---|---|---|
| A / Prototype | Function notes, key dimensions, photographs, drawing revision | It does not authorise mass production or confirm the production process |
| B / Pre-production | Tool or process ID, material lot, finish standard, packing method, measurements | It does not replace the label, artwork or carton-mark approval |
| C / Golden sample | Two signed masters, sample IDs, approval sheet, frozen file revision | It does not cover a later substitution unless the file is re-issued |
| D / First articles | First-off measurements, comparison to master, current revision checked | It does not waive the final inspection before balance payment |
| E / Reorder | Master file re-check, retained references, spares status, deviation history | It does not assume the previous purchase order still describes the goods |
Approve with a record, not with a message
Sample ID GS-xx, revision 03, approved against specification revision 03.- List the accepted deviations by number, and name the documents covered.
- State explicitly what remains open: artwork, labels, manual, carton marks.
- Name the signatory and date on both masters. Inspection will refer back to this text.
Looks good, go aheadwith no revision number attached.- A digital mockup presented as a physical colour standard.
- A sample from a different tool, material lot or finish than the production run.
- A substitution agreed in a chat thread; route it through the change process instead.
We do not certify products, do not issue test reports and are not a factory. Where a destination market requires testing or formal verification, confirm the requirement with a qualified compliance body or licensed broker and keep the resulting records in the same submittal index as the approval sheet.
Frequently asked questions
How many sample rounds should I expect?
More than one is normal for a custom configuration. The number matters less than whether each round answers a defined question and produces a written deviation record. Custom manufacturing describes the wider sequence.
Is a digital proof enough for packaging approval?
No. Approve a physical sample or draw-down on the actual substrate, because the same colour values shift between coated board, kraft and film. See custom packaging.
What is a golden sample and who keeps it?
A physically signed master that represents the agreed standard. Keep two with unique IDs, one on the buyer’s side and one at the factory, both tied to the same file revision. Inspection compares the finished run against it.
Can a change after approval keep the same golden sample?
Only if the change does not affect form, fit, function, appearance or the documents. Otherwise re-issue the file, update the master and consider a new first article check. Our desk holds that decision in writing.
Does an approved sample replace pre-shipment inspection?
No. The sample defines the standard; inspection checks the whole finished run against it, including quantity, packing, labels and carton marks. DDP shipping and entry documents then rely on the same description.
Send the specification and we will build the quote around it.
Include the product or drawing, the destination market, your quantity breaks, the changes you want made, and the documents your channel requires. We work as your sourcing, quality control and freight partner in China; we are not a factory and do not issue test reports or certificates.
WhatsApp / Phone: +86 186 7676 3055
Email: info@cinosourcing.com
Or use the contact form.
Part of our Custom Product Sourcing From China hub: specification control, tooling, sampling, inspection and shipping for wholesale, OEM and project orders.
