A uniform that survives one service is easy. One that survives two hundred industrial washes and still matches the jackets already in service is a specification.
For restaurant groups, hospitality operators and private-label uniform programmes sourcing from China.
A second site opens six months after the first, or a batch of chef jackets needs replacing after a season. The reorder looks straightforward: same style, same logo, same sizes. What usually goes wrong is not the sewing — it is that the first order was never written down as numbers. A colour was approved on a screen, a size was agreed as “Asian L”, and the laundry behaviour was never tested. This guide sets out the specification lines that make a reorder comparable with the first batch.
SECTION 01Why the second order is harder than the first
Uniforms are working garments. They go through hot industrial washing, contact with oil and steam, and repeated drying. A fabric that looks right on day one can shrink, thin out, fade or go stiff after a few cycles, and a dark indigo that matched in the first shipment can drift in the next dye lot. Add new staff, new sites and a different mill, and the buyer ends up with two visibly different uniforms under one roof. The commercial answer is not a cheaper mill; it is a written specification and a kept reference.
What buyers actually complain about. Shrinkage after washing, colour drift between batches, embroidery that cracks or peels, a size chart that does not match the local market, and care labels that do not survive the laundry. All five are specification problems, and all five are cheaper to settle before bulk than after.
SECTION 02Write the fabric as numbers, not adjectives
“Good quality poly-cotton” is not a specification. Each of the following lines should appear in writing before a sample is approved, because each one changes how the garment behaves in service:
| Spec line | What to put in writing | Why it matters |
|---|---|---|
| Composition | Fibre blend with percentages, e.g. a cotton/polyester ratio or a polyester/rayon/spandex blend approved for the style. | Determines shrinkage, breathability, drape and how the cloth takes print or embroidery. |
| Fabric weight & weave | Grammage or an agreed mill reference plus a physical swatch, not a description. | A lighter cloth may look identical and feel thinner after washing. |
| Shrinkage & colour fastness | Acceptable tolerance and the wash conditions the garment must withstand, agreed against a test or wash check. | This is what keeps a size chart and a brand colour stable across reorders. |
| Construction | Wrap-front or kimono-collar jacket, sleeve length, vent or side slits, ties, pockets, seam allowance and stitch density. | A change here alters fit even when the size label stays the same. |
| Branding method | Print or embroidery, position and size in centimetres, thread or ink reference, and any backing requirement. | Cracking, peeling and stiffness show up after washing, not on the sample table. |
Our product specification sheet guide shows how to put all of these into a single document, and the artwork handover checklist covers the vector files, placement and colour standards that go with it.
SECTION 03Sizing across regions needs a measurement table
Japanese, European and US size labels do not describe the same body, and a hand-measured chart can carry a small deviation even within one batch. Ask for the finished garment measurements in centimetres — chest width, back length, shoulder width and sleeve length — rather than a letter size. State which market the chart is for and whether the fit is intended to be relaxed enough to layer over other clothing.
| Column in the size chart | What to confirm |
|---|---|
| Size set | The full run (for example S to XXXL), split into adult, women’s and kids’ blocks where relevant. |
| Finished measurements | Chest, back length, shoulder and sleeve for every size, with the measuring method described. |
| Tolerance | The acceptable deviation per measurement, written into the order rather than assumed. |
| Quantity per size | A breakdown by site or store, so packing and carton labels can follow the delivery plan. |
| Name list | Where individual embroidery is used, a written list checked before digitising. |
Keep one approved garment per size as the physical reference. When the reorder arrives, it is measured against that reference, not against a memory of how the last batch fitted.
SECTION 04Industrial laundry is the real test
A sample that has never been washed tells you very little about a uniform. Before bulk is released, agree the washing conditions the garment must survive and check it after washing, not only flat on a table.
- Dimensional change — measure the same points before and after the agreed wash cycle.
- Colour — check for bleeding, fading and a visible difference against the approved swatch.
- Hand feel and fabric integrity — thinning, stiffness, pilling or a distorted weave.
- Branding — cracking, peeling, edge sharpness and the readability of small text.
- Seams and trims — ties, collar bands, labels and care labels after laundering.
These checks belong inside sample approval gates and first-article inspection. Our pre-shipment inspection then verifies the bulk against the same written specification before loading.
SECTION 05A repeat-order file that actually works
For a group reordering across sites, the file we keep is deliberately dull: the signed specification sheet, the approved swatch and print-position sheet, the size chart with tolerances, the label and care-label wording, the packing spec and the carton marking plan. When a mill, an ink batch or a component changes, engineering change control is how the change is recorded and approved rather than quietly introduced. Custom packaging and labelling covers woven labels, hang tags and per-piece polybags.
We work with restaurant groups holding repeat stock, private-label programmes and project buyers with an agreed volume. If your requirement is one or two garments for a single site, tell us what it is and we will say plainly whether the order is a fit before you spend time on it.
SECTION 06Pricing: one written all-in number
Our quoted price already includes our margin. There is no separate sourcing fee or commission added on top, and we do not set a strict MOQ of our own. Factory minimums vary by fabric, construction and branding method, and are confirmed in writing before any deposit. A quote shows the product, sampling, inspection, consolidation and freight as separate written lines inside one total, so you can compare it with your landed-cost model. See our repeat-order sourcing model and DDP shipping from China. We request and check factory-side paperwork; your compliance adviser confirms the labelling rules for your market, and we do not issue certifications or file customs declarations.
SECTION 07Frequently asked questions
Q · Can you match the colour of a uniform we already use?
We can work to a physical swatch and record an acceptable deviation, but an exact match cannot be promised across dye lots. The approved swatch stays on file and the new batch is checked against it before loading.
Q · Do you set a minimum order quantity?
No. We do not set a strict MOQ of our own; factory minimums vary by fabric and branding method and are stated in writing before any deposit. Our margin is already inside the quoted price, and in practice we support repeat-stock programmes and consolidated shipments.
Q · Can our logo be embroidered with individual staff names?
Yes. Send the vector logo, the position and size in centimetres, and a written name list. Names are checked before digitising because a misspelling cannot be repaired after stitching.
Q · What documents can you request from the factory?
Fabric composition and care labelling, colour-fastness and wash test reports, and applicable material declarations. We check the paperwork matches the goods; your compliance adviser confirms what your market requires.
SECTION 08Related reading
Send your current uniform photo and size breakdown
A photo of the garment in service, the fabric composition if you have it, and quantities per size are enough to start. We confirm the specification in writing and quote product, inspection, consolidation and freight as one all-in price.
