A tooth, an adapter nose, a pin and a retainer are one system. Order them as a set.
Different tooth families do not interchange. Identify the family before asking for a price.
Ground-engaging tools are the fastest-moving consumable on most fleets, and the easiest to order wrongly. Buyers ask for “bucket teeth for a 20-ton excavator” and receive a set built for a different locking system. Machine tonnage narrows the field; it does not identify the tooth. The cast number, the pin orientation and the pocket opening do.
Our rule. We do not cross one tooth family into another. Send the part number or a photo set, and we confirm the tooth, adapter, pin and retainer as one matched system in writing before any deposit.
SECTION 01Why a model name is not a tooth specification
- The same machine can be fitted with different bucket and adapter systems over its life.
- Side-pin, top-pin and hammerless locking systems look similar in a small photo but do not interchange.
- A worn tooth can hide the cast number; the pocket opening usually still shows the original fit.
- Teeth, pins and retainers wear at different rates, so a reorder of teeth alone often leaves the old locking parts in service.
SECTION 02Four checks that identify the family
| Check | Where to look | What it decides |
|---|---|---|
| Cast part number | Inside wall or rear edge of the tooth pocket, or stamped on the adapter | The tooth and adapter family; include suffixes, not just the base number |
| Pin orientation | Side of the tooth, or a rectangular hole on the top | Side-pin, vertical-pin or hammerless system |
| Pin & retainer measurement | Measure diameter and length of the pin and retainer, not the worn tooth | The fitment size. Pins are made to tighter tolerances than castings |
| Tooth pocket opening | Height and width of the rear opening of the pocket | Cross-check of the size, because the pocket wears less than the tip |
Machine tonnage is a useful starting point for narrowing a search, not a final answer. If the cast number is unreadable, the four checks above plus a photo of the old part fitted on the bucket are usually enough.
SECTION 03What a mismatched set actually costs
SECTION 04Build the order as one set
- Teeth. Profile chosen for the material: general digging, rock, abrasion-heavy or penetration-focused work. State the duty rather than a colour or a brand word.
- Adapters. Quote them when the nose is worn or when the bucket is being rebuilt. Record whether they are weld-on or bolt-on.
- Pins and retainers. Always reorder locking parts with the teeth, even when the old ones look usable.
- Side cutters and end bits. Add them to the same list so the whole wear edge reaches the site together.
- Spares share. Agree the spare quantity in writing on the quotation rather than leaving it to the packing team.
A quotation that lists only “bucket teeth” is not a specification. Ours lists the family, the part numbers, the locking system, the grade, the spare share and the packing method line by line.
SECTION 05The photo set that replaces a catalogue
- The machine plate and the bucket in place on the machine.
- The tooth from the side, showing the cast or stamped number.
- The pin and retainer removed from the tooth, next to a ruler or calliper for scale.
- The rear opening of the tooth pocket and the adapter nose, photographed square-on.
These four photos let a factory confirm the fit without a physical sample. Our part-number guide explains how the same principle applies to a whole excavator parts list.
SECTION 06Packing so small parts do not disappear
Teeth are dense and pins are small. Bag each tooth with its matching pin and retainer where the order allows it, label every carton with the line reference, and crate the heavy items so they do not crush the locking parts. Because GET is often only part of a mixed order, packing has to be planned with the rest of the container: see consolidating parts from several factories and heavy hardware freight economics.
SECTION 07Questions buyers ask
Q · Can teeth from one system be fitted to another adapter?
No. Nose profiles and locking systems differ. We confirm the family in writing rather than substituting a similar-looking part.
Q · Can I add teeth and pins to an order that already contains other parts?
Yes. A mixed container is the normal case, and small locking parts are the reason we plan packing and marking before the goods leave the factory.
Q · How do you charge for sourcing?
Our quoted price already includes our margin. There is no separate sourcing fee or commission added on top, and we do not set a strict MOQ of our own. Factory minimums vary by part and are confirmed in writing before any deposit.
Keep reading
Send a photo of the tooth, the pin and the pocket
We confirm the family and the matched set in writing and quote product, inspection, consolidation and freight as one all-in price.
