Excavator Undercarriage Parts: What to Send Before a Track Group Is Quoted

HEAVY EQUIPMENT SPARE PARTS · ROUND 2 / 01

A track group is quoted as a matched system, not as five separate part numbers.

track chaintrack shoessprocketsrollersidlerschain pitchshoe widthmatched set

Send the machine plate and a few measurements. We confirm fitment in writing before any deposit.

An undercarriage order usually goes wrong at the enquiry stage. A buyer sends a machine model, asks for a price on a track chain, and receives a quote for a chain that was built for a different serial range. The parts arrive, the mounting holes do not line up, and the machine stays on the site for another week. Undercarriage is the one category where a short enquiry costs the most to correct after shipping, because the parts are heavy, dimensional and sold as a group.

Where the numbers come from. Wear limits belong in your service manual, not in a supplier article. We do not publish prices, wear limits or lead times in a guide: we ask for measured readings, confirm the specification in writing, and then quote product, inspection, consolidation and freight as one all-in price.

SECTION 01Why an undercarriage enquiry fails before it reaches a factory

  • Model only. One model name can cover several production builds with different link pitch, shoe width, sprocket bolt circle and final drive spline. The serial plate decides which build.
  • Measured after failure. When a chain has already derailed, the worn part is often past measuring. Photos of the plate, the link side and the sprocket teeth taken at inspection are what make a cross-reference possible.
  • One grade word for the whole list. “Good quality” does not tell a factory whether the pins are induction hardened or whether the rollers use the same seal design. Grade belongs on each line.
  • Partial sets. Chain only, on a hooked sprocket, is the most common false economy in this category.

SECTION 02The six lines that have to be quoted together

Line What wears What to send
Track chain / link assembly Pitch elongation, bushing outside diameter, link side wear Link pitch, number of links per side, photo of the link side and the master pin
Track shoes & bolt kit Grouser height, elongated bolt holes, missing nuts Shoe width, single / double / triple grouser, bolt hole pattern, whether hardware is included
Sprockets or segments Hooked or pointed tooth profile Tooth count, bolt circle, photo of the final drive spline and the tooth profile
Front idler & recoil spring Seal leak, tread wear, tension loss Idler type, mounting bolt pattern, whether the recoil assembly is needed
Track & carrier rollers Flat spots, leaking seals, reduced tread diameter How many per side, flange type, positions to be replaced
Hardware & guards Stretched bolts, cracked guards Bolt, nut and chain guard kit quoted with the set

Matched-set rule. A new chain running on a worn sprocket will wear out quickly and can damage the new components. Plan the chain, shoes, sprockets, idlers, rollers and hardware together so the group reaches its service limit together.

SECTION 03The five-item pack to send with the enquiry

  1. Machine identification. Brand, model and serial number, plus a clear photo of the machine plate. The plate is faster than a typed model and avoids transcription errors.
  2. Part numbers. Numbers from the parts book, numbers cast or stamped on the old parts, and any cross-reference numbers you already use. Include superseded numbers rather than deleting them.
  3. Dimensions. Track gauge, chain pitch, shoe width, link count and any bolt pattern you can measure. The service manual is the reference, not the worn part.
  4. Photos. Machine plate, link side, sprocket teeth, roller or idler tread, and the old part fitted in place showing the mounting face.
  5. Duty and destination. Mining, quarry, general earthmoving or demolition; the destination country; and any packing requirement such as wooden crates or palletised sets.

If you only have the machine model, send it anyway. We will come back with the exact items needed to confirm the match instead of guessing from a catalogue.

SECTION 04Grades and what we put in writing

Matched set
The quotation lists every line in the group, including hardware, so a partial order cannot be shipped by mistake.
Grade per line
Material, heat treatment and seal design are stated for each line, not for the list as a whole.
Inspection scope
Which dimensions are checked, which test records are supplied, and what is photographed before loading.
Written field What it locks down
Part number & supersession The number being built to, and the current replacement if the old number was retired
Material & heat treatment The grade of pins, bushings, rollers and teeth, together with the verification method
Dimensional checks Pitch, width, bolt pattern and spline confirmation against the machine plate
Packing & marking Crate or pallet, anti-rust protection, and labels that identify each set
Inspection before loading What our pre-shipment inspection covers, and the evidence you receive

SECTION 05Weight, packing and the container plan

Undercarriage is heavy, dense cargo. It is usually the line that decides how a mixed container is loaded. Steel parts need anti-rust protection, small hardware needs to be bagged and labelled per set, and crates need to be planned before the parts leave the factory rather than at the warehouse. Our heavy hardware freight guide explains the weight and cube logic, and consolidating metal parts shows how several factories become one shipment. Door-to-door options are covered in DDP shipping from China.

SECTION 06A reorder file that makes the next order faster

  • Keep one file per machine serial number, not per model name.
  • Record the measured readings, the replacement date and the grade that was supplied.
  • Keep the plate photo, the fitment photos and the written specification together.
  • On the next order, send the file. The match is already documented. Our repeat-order guide for spare parts uses the same principle.

SECTION 07Questions buyers ask

Q · Can I order only a track chain?

Yes, but we will ask for the sprocket tooth profile and roller condition first. If they are worn, we will say so in writing before the order is placed.

Q · Do you hold stock or publish a catalogue?

We work from your part numbers, plate and photos, and source from verified Chinese factories. There is no fixed catalogue to browse; the excavator and wheel loader parts page explains the full process.

Q · How are your fees charged?

Our quoted price already includes our margin. There is no separate sourcing fee or commission added on top, and we do not set a strict MOQ of our own. Factory minimums vary by part and are confirmed in writing before any deposit.

Keep reading

ONE WRITTEN SPEC · ONE ALL-IN PRICE

Send the plate and the measurements, not a catalogue request

One parts list, several verified factories, one written specification and one consolidated shipment. We confirm the match in writing and quote product, inspection, consolidation and freight as one all-in price.

Request a quote WhatsApp us

Leave a Comment

Your email address will not be published. Required fields are marked *